Did you know?

After I replaced the DFI sensor on my Litter Robot 3 I started getting a flashing red light--whether or not there is anything in the robot at all. Then when I press reset it changes to a flashing yellow light and the app says "Bonnet Removed". ... Use some petroleum jelly to encase the contact point of the pinch detect switch afterwards to ...Disassemble. 1. Turn the base over so it is upside down. 2. Remove the 9 screws connecting the bottom of the base to the top of the base. 1 screw at the back of the unit behind the black cat sensor foot. 3. Gently lift to separate the two halves of the base. The pieces will still be connected by a wire. Keep your automatic litter box in top shape for years to come with Litter-Robot replacement parts and refresher items. Use our DIY installation guides and videos.Purchase replacement pinch contact and drawer full indicator (DFI) circuit board assembly for your Litter-Robot 3. The store will not work correctly in the case when cookies are disabled. JavaScript seems to be disabled in your browser.Details. Purchase replacement pinch contacts and drawer full indicator (DFI) circuit boards for your Litter-Robot 3. Contact Whisker Support if your robot is still under warranty. Specs. FAQ. The Litter-Robot 3 Open Air DFI Hardware (v2) is a replacement DFI Hardware for your Litter-Robot 3. It is compatible with Litter-Robot 3 only. What's Included. 1x Litter-Robot 3 Open Air DFI Hardware (v2) Specifications. Compatible with Litter-Robot 3 only.From bundles and furniture to parts and accessories, shop all Litter-Robot products in one place. Litter Robot III Installing DFI Sensors Kit. Cat Evolution. 14K views 2 years ago. Litter Robot 3 Fast Flashing Blue & Random lights - Repair Guide.Litter Robot Pinch Contact And DFI Kit. Stop scooping today and give your cat a clean bed of litter for each use with a reconditioned model of the highest-rated automatic, self-cleaning . Litter-Robot Pinch Contact DFI Kit. Litter-Robot 3: Checking the Pinch Detect. Litter-Robot Pinch Contact DFI Kit ...The Litter-Robot 3 Open Air DFI Hardware (v2) is a replacement DFI Hardware for your Litter-Robot 3. It is compatible with Litter-Robot 3 only. What's Included. 1x Litter-Robot 3 Open Air DFI Hardware (v2) Specifications. Compatible with Litter-Robot 3 only.Litter-Robot 3: Checking the Pinch Detect. Watch on. The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times ...Tap that about 10x (litter gets caught in it). Then on that same square, reach your fingers in and then wrap around that same left side. there are metal connectors that are the pinch detectors. they have to stay touching. If you push them up they will sit again the plastic and touch flush. JmKz19 • 17 hr. ago.Our litter robot 3 has been barely working for a while. I'd have to hit reset and cycle for it to actually work. Well, about 2 weeks ago it over rotated during a cycle and became "stuck" (wouldn't rotate back into starting position). Putting it back manually caused a yellow flashing light that wouldn't go away.

The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. Litter Robot III Installing DFI Sensors Kit. Cat Evolution. 14K views 2 years ago. Litter Robot 3 Fast Flashing Blue & Random lights - Repair Guide.What you described is classic DFI failure. The reason it fails is because of moisture intrusion of the moisture barrier on the DFI. About a year in to use is the average time for the moisture to cause bad solder joints on the I/O chip located on the Emitter board of the DFI set, (you will see black corrosion on the chip pins) This will display the symptoms you have …Came home to my Litter-Robot in the upside down position and the yellow flashing (2 flashes per second) and I cannot get the globe to turn at all to try to reset itself. ... it isn’t due to the DFI. It’s either the motor, the anti-pinch or the bonnet connections, depending on the flashing speed. ... Remember, this is the replacement DFI ...

by Infamous_IceBear. Anyone else have wifi problems after replacing the Pinch Contact & DFI kit?! I've had my LR3 since 2019. This week, I replaced the Pinch Contact & DFI …Purchase replacement pinch contacts and drawer full indicator (DFI) circuit boards for your Litter-Robot 3. Contact Whisker Support if your robot is still under warranty The store will not work correctly in the case when cookies are disabled. …

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Blue flashing light fast flashing yellow light may. Possible cause: by alexamaxwell. Help with pinch detector. Hi! So I am so over the litter r.